Back to summary

Shell PWD

Case: 20260511T111256Z__continue-cli__local_pleasecech_qwen3_6_plus_latest__ollama__tool__shell_pwd

CLI Agent: continue-cli 1.5.45 | CLI Agent Version: 1.5.45

TOOL_UNSUPPORTED Trajectory: clean | Invoked: no | Match: 0%

Failure Reason: tool unsupported by backend

Shell Commands

Warmup

cn --allow shell --config /work/results/runs/20260511T111256Z/cases/continue-cli__local_pleasecech_qwen3_6_plus_latest__ollama__tool__shell_pwd/runtime/continue-cli/warmup/home/.continue/config.yaml -p --auto --silent 'Use the shell tool. Run exactly this command: pwd > pwd-output.txt.
Do not retry on error.
If the command fails, reply only with FAIL and stop.
If the command succeeds, reply only with DONE and stop.
Do not continue reasoning after DONE.
Do not call any additional tools after DONE.
End your response immediately after DONE.
'

Measured

cn --allow shell --config /work/results/runs/20260511T111256Z/cases/continue-cli__local_pleasecech_qwen3_6_plus_latest__ollama__tool__shell_pwd/runtime/continue-cli/measured/home/.continue/config.yaml -p --auto --silent 'Use the shell tool. Run exactly this command: pwd > pwd-output.txt.
Do not retry on error.
If the command fails, reply only with FAIL and stop.
If the command succeeds, reply only with DONE and stop.
Do not continue reasoning after DONE.
Do not call any additional tools after DONE.
End your response immediately after DONE.
'

Trajectory Hints

Prompt

Use the shell tool. Run exactly this command: pwd > pwd-output.txt.
Do not retry on error.
If the command fails, reply only with FAIL and stop.
If the command succeeds, reply only with DONE and stop.
Do not continue reasoning after DONE.
Do not call any additional tools after DONE.
End your response immediately after DONE.

Expected vs Observed

No expected/observed content.

Session Transcript

No structured session transcript found.

Tool / Process Output

Warmup stdout

[gripprobe] process_started_at=2026-05-11T11:13:26+00:00

[gripprobe] process_finished_at=2026-05-11T11:13:30+00:00 exit_code=1

Warmup stderr

[gripprobe] process_started_at=2026-05-11T11:13:26+00:00
{"status":"error","message":"400 registry.ollama.ai/pleasecech/qwen3.6-plus:latest does not support tools"}

[gripprobe] process_finished_at=2026-05-11T11:13:30+00:00 exit_code=1

Measured stdout

[gripprobe] process_started_at=2026-05-11T11:13:30+00:00

[gripprobe] process_finished_at=2026-05-11T11:13:34+00:00 exit_code=1

Measured stderr

[gripprobe] process_started_at=2026-05-11T11:13:30+00:00
{"status":"error","message":"400 registry.ollama.ai/pleasecech/qwen3.6-plus:latest does not support tools"}

[gripprobe] process_finished_at=2026-05-11T11:13:34+00:00 exit_code=1

Model Modelfile (Ollama)

# Modelfile generated by "ollama show"
# To build a new Modelfile based on this, replace FROM with:
# FROM pleasecech/qwen3.6-plus:latest

FROM /usr/share/ollama/.ollama/models/blobs/sha256-48b3ba219908d335b4e34b61694d968163f05727fab579da8daac5c9fdf37eb1
TEMPLATE {{ .Prompt }}